Ram Audio W 9000 DSP PA Power Amplifier 2 x 4400 W 2 Ohms incl. DSP Module
€5,818.75 *
Availability:
Currently not available
Currently not available
Item number: 500121800
if the power supply draws excessive current under laboratory conditions or during extended... more
All information about the product:
"Ram Audio W 9000 DSP PA Power Amplifier 2 x 4400 W 2 Ohms incl. DSP Module"
- high-efficiency power amplifiers with up to 12 kW RMS output power
- regulated PFC QuantaPulse dual switch-mode power supply
- digital control with large blue LCD interface
- temperature and output level indication
- USB port for firmware updates and DSP control
- gain, bridge mode, input links and ICL configurable via 13-detent digital encoders on the front panel
- RAM Audio power management system (PMS)
- high-efficiency oversized output transistors for maximum reliability under extreme operating conditions
- easily removable front panel for dust filter cleaning, Neutrik XLR and Speakon connectors
- if the internal operating temperature approaches emergency shutdown during irregular operating conditions, ICL?: improved Intelligent Clip Limiting prevents loudspeaker damage while maintaining audio quality and punch under clipping conditions. QuantaPulse? Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.Specifications:
Product type: | Power Amplifiers |
Type: | PA Power Amplifiers |
Weight: | 12,5 kg |
Product type: | Power Amplifiers |
Type: | PA Power Amplifiers |
Rated ouput power (1kHz @ 2 Ohms): | 2 x 4400 W |
Rated ouput power (1kHz @ 4 Ohms): | 2 x 2300 W |
Rated ouput power (1kHz @ 8 Ohms): | 2 x 1200 W |
Rated ouput power (1kHz @ 4 Ohms, bridged): | 8800 W |
Rated ouput power (1kHz @ 8 Ohms, bridged): | 4600 W |
High Z 100Vrms / 140Vpeak: | 2 x 4400 W |
Output circuitry: | Class H |
Frequency response: | 20 - 20000 Hz |
THD: | < 0.05 % |
Signal-to-noise ratio: | 115 dB |
Damping factor: | > 500 |
Crosstalk: | > 80 dB |
Gain: | 26 - 38 dB |
Input sensitivity: | 4.9 / 2.5 / 1.2 V |
Input impedance: | (balanced) 20 k Ohm(s) |
Input impedance: | (unbalanced) 10 k Ohm(s) |
Protection circuits: | on/off transients |
Protection circuits: | Soft start |
Protection circuits: | thermal overload |
Protection circuits: | DC voltage |
Protection circuits: | high frequency |
Protection circuits: | open outputs and speaker load mismatching |
Protection circuits: | power on muting |
Protection circuits: | short circuit |
Controls: | Power |
Controls: | 2 x volume |
Controls: | dual/bridge switch |
Indicators: | signal |
Indicators: | temperature |
Indicators: | Clipping |
Indicators: | fault |
Indicators: | ready |
Line inputs: | 2 |
Line input connectors: | XLR |
Line outputs: | 2 |
Line output connectors: | XLR |
Loudspeaker outputs: | 2 |
Speaker output connections: | Speakon |
Cooling: | fan |
Operating voltage: | 230 V |
Power consumption @ full load: | 10 A |
Width: | 483 mm |
Height: | 89 mm |
Depth: | 460 mm |
Weight: | 12 kg |
Product type: | Power Amplifier Accessories |
Type: | 2-channel |
AD/DA converter: | 24 bit |
Filter type: | Bessel |
Filter type: | Butterworth |
Filter type: | Linkwitz-Riley |
Filter slew rate: | up to 48 dB/oct |
Input EQ: | 29 x graphic or parametric per channel |
Output EQ: | 20 filters per channel (parametric, shelving, LP, HP, BP, SB) |
Input delay: | up to 80 m (230 ms) per input |
Output Delay: | up to 18 m (50 ms) per channel |
Limiter (per channel): | Peak Voltage Output (variable knee) |
Limiter (per channel): | RMS Power |
Additionakl DSP functions (per input): | Gain |
Additionakl DSP functions (per input): | mute |
Additionakl DSP functions (per input): | Phase Inversion |
Additionakl DSP functions (per channel): | Gain |
Additionakl DSP functions (per channel): | Phase Inversion |
Additionakl DSP functions (per channel): | mute |
Line inputs: | 2 |
Line input connectors: | XLR (balanced) |
Line outputs: | 2 |
Line output connectors: | XLR (balanced) |
Programming: | Ethernet (optional) |
Programming: | via USB port |
Other features: | Signal Generator (pink and white noise, sinus 20 Hz - 20,000 Hz) |
Weight: | 0,5 kg |
Further links
We will be happy to advise you!
You can reach us:
Mon-Fri: | 08:00 am – 05:00 pm |
You can find answers to frequently asked questions here:
LTT-InfoCenter
More than 50,000 products
Shipping free* from €40
Fast delivery
3-year LTT guarantee
Purchase on account: Buy safely!
Downloads for the product:
"Ram Audio W 9000 DSP PA Power Amplifier 2 x 4400 W 2 Ohms incl. DSP Module"
Document type | File size | |
Information about the product
(2.11 MB)
|
2.11 MB | |
Information about the product
(0.40 MB)
|
0.40 MB | |
Information about the product
(12.96 MB)
|
12.96 MB |
We will be happy to advise you!
You can reach us:
Mon-Fri: | 08:00 am – 05:00 pm |
You can find answers to frequently asked questions here:
LTT-InfoCenter
More than 50,000 products
Shipping free* from €40
Fast delivery
3-year LTT guarantee
Purchase on account: Buy safely!
We will be happy to advise you!
You can reach us:
Mon-Fri: | 08:00 am – 05:00 pm |
You can find answers to frequently asked questions here:
LTT-InfoCenter
More than 50,000 products
Shipping free* from €40
Fast delivery
3-year LTT guarantee
Purchase on account: Buy safely!