Which cable should I use for a power distributor?

For professional power distributors in event technology, use H07RN-F rubber cable with appropriate cross-section for the load. For 16A CEE distributors, 5×1.5 mm² (five-core: three phases, neutral, earth) is the minimum, though 5×2.5 mm² offers better safety margins and lower voltage drop. For 32A distributors, use 5×4.0 mm² or larger. Rubber-sheathed H07RN-F cable is oil-resistant, flexible and suitable for outdoor use, making it ideal for mobile event applications. Brands like Titanex offer enhanced durability for demanding touring environments.

What is the difference between 16A and 32A CEE connectors?

CEE 16A and 32A connectors differ in size, current capacity and typical applications. A 16A CEE connector (red, 400 V three-phase) handles up to 11 kW continuous load, suitable for most stage lighting rigs and small to medium PA systems. The 32A variant supports up to 22 kW, used for larger productions, multiple distributed loads or high-power equipment like large moving lights and amplifier racks. Physically, 32A connectors are larger with thicker pins, and they require correspondingly larger cable cross-sections (typically 5×4.0 mm² vs. 5×1.5 mm² for 16A). The two types are not interchangeable — a 16A plug will not fit a 32A socket.

When do I need a DMX terminator?

A DMX terminator is required on any DMX512 lighting control network longer than approximately 50 metres or with more than 20 fixtures in the daisy chain. The terminator — a 120-ohm resistor connected between DMX pins 2 and 3 (Data+ and Data–) — is installed at the last fixture in the chain. It absorbs signal reflections that would otherwise bounce back along the cable, causing data corruption, flickering or erratic fixture behaviour. Without proper termination, long cable runs or large fixture counts often result in unreliable operation, especially with fast-moving effects or strobing. Professional DMX terminators are available as XLR plug-in modules, or you can solder a 120-ohm resistor into a spare XLR connector.

What types of plug connections are used in event technology?

Professional event technology uses several standardised connector types. CEE connectors (IEC 60309) in 16A, 32A and 63A variants handle three-phase power distribution, with colour coding (blue for 230 V, red for 400 V) preventing mis-connection. Schuko (Schutzkontakt) plugs and sockets are standard for 230 V single-phase equipment. XLR connectors in 3-pin and 5-pin versions carry DMX lighting control and analogue audio signals. powerCON connectors (by Neutrik) provide a locking mains connection for powered loudspeakers and lighting fixtures, safer and more reliable than IEC C13/C14. Speakon connectors (also Neutrik) are the professional standard for speaker cables, offering secure locking and high current capacity. Each connector type is optimised for its specific application, ensuring safety and reliability in demanding production environments.

How do I calculate the load for a power distributor?

To calculate the load for a power distributor, sum the power consumption (in watts) of all connected equipment, then divide by the supply voltage to obtain current in amperes. For single-phase 230 V loads, use the formula: Current (A) = Power (W) ÷ 230. For three-phase 400 V loads, the calculation is: Current (A) = Power (W) ÷ (√3 × 400) ÷ efficiency factor. Always add a 20–30% safety margin to account for inrush currents, power factor and future expansion. Ensure loads are balanced across all three phases (L1, L2, L3) to prevent neutral overload. Check that the total current does not exceed the distributor's input rating (e.g. 16A for a CEE 16A input) and that individual outlet circuits remain within their rated capacity.

Which DMX cable should I buy for stage lighting?

For professional stage lighting, always use purpose-designed DMX512 cable with 110-ohm impedance and twisted-pair construction. Look for cables with robust shielding (foil plus braid, minimum 90% coverage) to prevent interference from nearby power cables. Brands like Sommer Cable, Cordial and Helukabel offer high-quality DMX cables with flexible, durable jackets suitable for touring. Choose 3-pin XLR for standard applications or 5-pin XLR for future compatibility and enhanced grounding. Avoid using standard microphone cables for DMX — they lack the correct impedance and shielding, leading to signal errors and unreliable operation. For permanent installations, specify UV-resistant or flame-retardant jackets as required by the environment.

What does IP44 protection mean for power distributors?

IP44 (Ingress Protection rating 44) indicates that a power distributor is protected against solid objects larger than 1 mm (e.g. wires, small tools) and against water splashes from any direction. The first digit (4) denotes protection against solid particles; the second digit (4) denotes protection against water. IP44 is the minimum standard for outdoor event equipment, ensuring safe operation in rain, damp conditions and dusty environments like festival sites or construction areas. However, IP44 does not mean the equipment is waterproof — it should not be submerged or exposed to high-pressure water jets. For harsher conditions, look for IP54 (dust-protected) or IP67 (dust-tight and waterproof) distributors.

How long can a DMX cable run be before signal quality degrades?

A properly terminated DMX512 cable run can reliably extend up to 300–400 metres before signal degradation becomes problematic, though the official DMX512 specification recommends a maximum of 250 metres. Beyond this distance, signal attenuation, capacitance and electromagnetic interference increase the risk of data errors, resulting in flickering, colour shifts or fixture dropouts. For longer runs, use a DMX splitter or booster to regenerate the signal — these devices receive the incoming DMX data, clean it up and retransmit it at full strength, effectively resetting the distance limit. Optical DMX systems extend this further, converting electrical signals to light and transmitting over fibre-optic cable for distances exceeding several kilometres with zero signal loss or interference.

Cables, Connectors & Power Distributors

DAP XLR 3p. Verbinder male, Schwarz/Endkappe Grün

DAP-Audio XLR 3P Connector - male - black housing Green end cap

Green end cap : PCB Mount: No • Housing: Metal • Colour: Black • Bushing Colour: Green • Locking Device: Latch • Contact Type: Nickel plated •

€1.11 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP XLR 3p. Verbinder male, Schwarz/Endkappe Rot

DAP-Audio XLR 3P Connector - male - black housing Red end cap

Red end cap : PCB Mount: No • Housing: Metal • Colour: Black • Bushing Colour: Red • Locking Device: Latch • Contact Type: Nickel plated •

€1.11 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP XLR 3p. Verbinder male, Schwarz/Endkappe Blau

DAP-Audio XLR 3P Connector - male - black housing Blue end cap

Blue end cap : PCB Mount: No • Housing: Metal • Colour: Black • Bushing Colour: Blue • Locking Device: Latch • Contact Type: Nickel plated •

€1.11 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio XLR-3P-Stecker – männlich – Nickelgehäuse, grüne Endkappe

DAP-Audio XLR 3P Connector - male - nickel housing Green end cap

Green end cap : PCB Mount: No • Housing: Metal • Colour: Silver • Bushing Colour: Green • Locking Device: Latch • Contact Type: Nickel plated •

€1.02 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP XLR 3p. Verbinder male, Nickel/Endkappe Gelb

DAP-Audio XLR 3P Connector - male - nickel housing Yellow end cap

Yellow end cap : PCB Mount: No • Housing: Metal • Colour: Silver • Bushing Colour: Yellow • Locking Device: Latch • Contact Type: Nickel plated •

€1.02 *

incl. tax, plus shipping costs

Availability:

Currently not available

Cablehood Side Entry PG29 Grey, 24/108 Pole

ILME 24/108P Cablehood Side Entry PG29 Grey, 24/ 108-pin

Hood for two levers, size "104.27", side entry, Pg29, metal version, IP66, Grey, 24/108-pin : Pins: 24 • Colour: Gray •

€14.90 *

incl. tax, plus shipping costs

Availability:

Currently not available

Chassis Closed Bottom with Clips PG29 Grey, 24/108 Pole

ILME 24/108P Chassis Closed Bottom PG29 Grey with Clips

Surface mounting housing with 2 levers, size "104.27", Pg29, metal version, IP66 : Pins: 24 • Colour: Gray •

€37.50 *

incl. tax, plus shipping costs

Availability:

Currently not available

Audio Insert Female Without Contactpins, 108 Pole

ILME 108P Audio Insert female Without Contactpins

Female insert, 108-pins + PE, crimp connections, 10 A, 250 V, 4 KV, 2, size "104.27", CLASS insert series. Delivered without contact pins : Pins: 108 • Minimum Wire Size: 0.5...

€14.50 *

incl. tax, plus shipping costs

Availability:

Currently not available

Audio Pole Insert Male Without Contactpins, 108

ILME 108P Audio Pole Insert male Without Contactpins

Male insert, 108-pins + PE, crimp connections, 10 A, 250 V, 4 KV, 2, size "104.27", CLASS insert series. Delivered without contact pins. : Pins: 108 • Minimum Wire Size: 0.5 mm²...

€13.90 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-DMXTERM-5/SET

5 pin DMX terminal resistor - 110 Ohm - Black Metal version

€4.81 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-A-RF/RF

Adapter RCA coupler to RCA coupler

€0.24 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-A-XM3/RF XLR 3 pol M-RCA female

Adapter plug 3pin XLR male to RCA coupler - Metal version

€1.52 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-A-XF3/J6M XLR3pol F- Jack 6,3mm mono

Adapter plug 3pin XLR female to 6,3 Jack mono - Metal version

€1.77 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-A-XM3/J6S XLR 3pol M - 6,3mm stereo

Adapter plug 3pin XLR male to 6,3 Jack coupler stereo - Metal version

€1.81 *

incl. tax, plus shipping costs

Availability:

Currently not available

AC-A-XM3/XM3

Adapter plug 3pin XLR male to 3pin XLR male - Metal version

€2.00 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL82 - IP65 DMX/AES-EBU XLR/M 3p. > XLR/F 3p. Neutrik - 6 m

DAP-Audio FL82 - IP65 DMX/AES-EBU XLR/M 3P to XLR/F 3P Neutrik XX HD 6 m

: Cable Length: 6 m •

€39.90 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL83 - IP65 DMX/AES-EBU XLR/M 5p. > XLR/F 5p. Neutrik - 1,5 m

DAP-Audio FL83 - IP65 DMX/AES-EBU XLR/M 5P to XLR/F 5P Neutrik XX HD 1.5 m

: Cable Length: 1.5 m •

€52.50 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL83 - IP65 DMX/AES-EBU XLR/M 5p. > XLR/F 5p. Neutrik - 3m XX

DAP-Audio FL83 - IP65 DMX/AES-EBU XLR/M 5P to XLR/F 5P Neutrik XX HD 3 m

: Cable Length: 3 m •

€54.90 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL84 - DMX/AES-EBU XLR/M 5p. > XLR/F 5p. Neutrik - 3 m

DAP-Audio FL84 - DMX/AES-EBU XLR/M 5P to XLR/F 5P Neutrik 3 m

: Cable Length: 3 m •

€56.50 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL74 XLR M/F Mic/Linecable - 10 mtr Neutrik

DAP-Audio FL74 XLR M/F Mic/Line Cable Neutrik XX series 10 m - silver plated

Microphone/line cable constructed out of MC-226 double insulated cable and Neutrik NC3 mXX + NC3FXX cable connectors. 3-pin male and female cable connectors with Nickel housing and silver contacts....

€28.90 *

incl. tax, plus shipping costs

Availability:

Currently not available

DAP-Audio FL74 XLR M/F Mic/Linecable - 3 mtr Neutrik

DAP-Audio FL74 XLR M/F Mic/Line Cable Neutrik XX series 3 m - silver plated

Microphone/line cable constructed out of MC-226 double insulated cable and Neutrik NC3 mXX + NC3FXX cable connectors. 3-pin male and female cable connectors with Nickel housing and silver contacts....

€21.50 *

incl. tax, plus shipping costs

Availability:

Currently not available