What are pre-assembled cables?

Pre-assembled cables are electrical or signal cables that arrive with connectors already attached at one or both ends. They are factory-terminated using professional crimping or soldering techniques, then tested for continuity and insulation integrity. In event technology, pre-assembled cables include DMX lighting cables, XLR audio snakes, powerCON mains feeds, and speakON loudspeaker assemblies. The main advantage is eliminating field termination errors and reducing installation time on-site. Each cable is built to precise length specifications with proper strain relief and shielding, ensuring reliable performance in touring and fixed installations.

What does cable assembly mean?

Cable assembly refers to the process of attaching connectors to cable ends and testing the finished product for electrical and mechanical integrity. Professional cable assembly involves stripping the cable jacket to the correct depth, preparing individual conductors, crimping or soldering contacts into connector housings, and installing strain relief components. The assembly is then subjected to continuity testing, insulation resistance measurement, and sometimes high-voltage dielectric testing. In event technology, cable assembly ensures that DMX, audio, and power cables meet industry standards for impedance, shielding effectiveness, and contact resistance, reducing the risk of failures during live events.

What are the advantages of pre-assembled cables over bulk cable?

Pre-assembled cables eliminate the need for on-site termination, saving installation time and reducing the risk of wiring errors. Factory assembly guarantees consistent quality through automated cutting, crimping, and 100% functional testing. Professional assemblies use strain relief and shielding techniques that are difficult to replicate in the field, especially under time pressure during event setup. Pre-assembled cables also arrive at precise lengths, eliminating waste and ensuring clean cable runs. For touring productions, the reliability of factory-tested assemblies reduces downtime and troubleshooting costs. The trade-off is higher upfront cost compared to bulk cable, but the time savings and reduced failure rate typically justify the investment.

Which connector types are standard for stage audio cables?

Stage audio cables primarily use XLR connectors for balanced microphone and line-level signals, following the IEC 61076-2-103 standard. Three-pin XLR connectors are standard for mono signals, with pin 1 carrying the shield, pin 2 the positive signal, and pin 3 the negative signal. SpeakON connectors are the industry standard for loudspeaker connections, with NL4 variants providing four poles for bi-amped systems. Quarter-inch TRS (tip-ring-sleeve) jacks are used for instrument cables and some line-level connections. Neutrik manufactures the majority of professional audio connectors, with XX series XLR and NL series speakON models dominating the touring market.

What is the difference between PVC, TPE, and PUR cable jackets?

PVC (polyvinyl chloride) jackets are economical and flame-resistant but become brittle below 0 °C and degrade under UV exposure and oils. They suit indoor fixed installations. TPE (thermoplastic elastomer) jackets remain flexible from –40 °C to +80 °C, resist oils and solvents, and are halogen-free, making them ideal for portable outdoor setups. PUR (polyurethane) jackets offer the highest abrasion resistance and are the standard for touring-grade cables, withstanding repeated coiling and mechanical stress. PUR resists oils, fuels, and UV light, and maintains flexibility down to –30 °C. PUR cables cost approximately 30% more than TPE equivalents but last significantly longer in demanding touring environments.

How long can a DMX cable run be before signal degradation occurs?

DMX512 protocol specifies a maximum cable run of 300 metres between the console and the last fixture in a daisy chain, assuming properly specified cable with 120 Ω impedance and low capacitance. Beyond 300 metres, signal reflections and attenuation can cause flickering, missed commands, or complete data loss. To extend DMX networks beyond this limit, use DMX splitters or opto-isolators that regenerate the signal. Each splitter output can drive another 300-metre run. Cable quality significantly affects maximum distance – professional DMX cables with foil shielding and twisted pairs maintain signal integrity better than repurposed microphone cables. Always terminate the last fixture in a DMX chain with a 120 Ω resistor to prevent reflections.

What does a professional audio snake cost?

Professional audio snakes vary in price based on channel count, length, and construction quality. A basic 8-channel snake at 15 metres with XLR connectors costs approximately €80–€120. A 16-channel snake at 30 metres ranges from €180 to €280, while a 24-channel snake at 50 metres costs €350–€600. Touring-grade snakes with individually shielded pairs, PUR jackets, and Neutrik connectors command premium prices – a 32-channel snake at 60 metres can exceed €800. Stage boxes with integrated connectors add €100–€300 to the price. Custom-length assemblies and hybrid snakes combining audio, DMX, and power lines are available at higher price points. Investing in quality snakes reduces failures and extends service life in demanding touring environments.

When should pre-assembled cables be replaced?

Pre-assembled cables should be replaced when they show signs of mechanical damage, electrical degradation, or intermittent failures. Visible indicators include cracked or abraded jackets, exposed conductors, bent or corroded connector pins, and loose strain relief. Electrical symptoms include crackling noise, intermittent signal loss, or complete failure during continuity testing. Cables used in touring environments typically require replacement every 3–5 years, depending on usage intensity and handling practices. Inspect cables before each event for jacket damage, connector integrity, and cable flexibility. Test audio and DMX cables with a cable tester to verify continuity and shielding effectiveness. Retire cables that fail insulation resistance tests or show intermittent faults, as they pose safety risks and can cause equipment damage.

Close menu

LTT-Versand englisch

Ready-made cables

Categories

Special cables for light effects

show

Miscellaneous video cables

show

695 Articles

Filter

Sorting

Close filters

Express delivery possible

Manufacturer

Accu Cable
Adam Hall Cables
Adam Hall Hardware
American DJ
Artecta
beamZ Pro
Cameo
DAP-Audio
dB Technologies
Eurolite
Expolite
Futurelight
IMG Stageline
JTS
LD Systems
MagicFX
MONACOR
Neutrik
Omnitronic
PD-Connex
PSSO
Riggatec
Seetronic
Showtec
SLV
SOMMER CABLE
Sonstige

Price

from 1.83 to 1299.48

3 From 29 pages

Products per page

No results were found for the filter!

Showtec Extension Cable, 32A 415V, 5 x 6,0 mm2 10 m

DAP-Audio Extension Cable - 32 A/380 V - 5x 6 mm² 10 m

High power extension cords. All extension cords are made of 5 x 6 mm Lineax neopreen cable and are fitted with PCE CEE connectors. : Rated Current (A): 32 A • Connector 1: CEE5P 32 A...

€171.33 *

incl. tax, free shipping to Germany
[International shipping costs]

Availability:

Delivery time: 3-5 days

Delivery time: 3-5 days

American DJ DMX Kabel XLR/XLR 5-Pin 10m

High quality, ready-made DMX cable : Connecting cable • 5 Pin XLR • Length: 10 m • Color: Black •